Introduction

Peripheral nerve injuries of varying degrees of severity often lead to permanent loss of sensory and motor function(Navarro et al., 2007). Treatment of peripheral nerve injuries frequently result in inadequate functional recovery,especially for nerve gap-injuries when a tension-free direct neurorrhaphy cannot be performed (Grinsell and Keating,2014). Autologous nerve grafts are the gold standard treatment for nerve gap-injury repair, but even this treatment often leads to insufficient functional recovery and causes loss of function at the donor site (Lee and Wolfe, 2000). Alternatives to the autograft are bioresorbable hollow guidance conduits and decellularized allogenic nerve grafts. Clinically available nerve conduits provide gross approximation of the two severed nerve ends for crude guidance of regenerating axons, while decellularized allogenic nerve grafts provide the topological and chemical guidance cues of native nerve extracellular matrix (Cho et al., 2012). Decellularized allogenic nerve grafts can be considered the greatest advancement of clinically available nerve repair devices, but these still are not as efficacious as the autograft in long-gap nerve repair (＞ 3 cm). A clinical need still exists to improve patient outcomes after peripheral nerve injury of all severities.

The majority of clinically available nerve repair devices lack added functionality. An intriguing small-molecule that has been widely studied in peripheral nerve regeneration applications is FK506 (Tacrolimus). FK506 is an FDA approved immunosuppressant drug used to prevent allograft organ rejection. FK506 can improve functional outcomes in vivo after peripheral nerve inury via multiple mechanisms of action including neurotrophic effects and reduction of scar formation (Gold et al., 1994, 1995; Que et al., 2012, 2013; Yan et al., 2012). Clinical adoption of FK506 has not occurred because the bene fi ts are not perceived to outweigh the harsh systemic toxicity and immunosuppresive effects associated with long-term systemic use (e.g., kidney toxicity, liver toxicity, increased risk of infection) (Felldin et al., 1997; Naesens et al., 2009; Konofaos and Terzis, 2013). Localized delivery of FK506 to a nerve injury/repair site could provide the peripheral nerve regeneration enhancing effects without the injurious side-effects associated with systemic use. Additionally,topological guidance cues are a critical component for sustaining nerve regeneration across large gaps (Ide et al., 1983;Hoffman-Kim et al., 2010). Previous studies by us and others have shown that longitudinally aligned surface micropatterns can increase neurite extension and neural cell alightment in vitro (Vaidya et al., 1998; Yao et al., 2009; Su et al., 2013; Li et al., 2014, 2018). Previously, we conducted micropattern optimization studies to investigate the effect pattern size had on neuronal cell extension, orientation, and viability. Results indicated that 10 μm ridges spaced by 10 μm grooves and 30 μm ridges spaced by 30 μm grooves were the optimal micropattern dimensions (Figure 1).

Figure 1 Scanning electron microspcopy images of micropatterned fi lms.(A) 10/10 μm fi lm, scale bar: 10 μm, 1000× magni fi cation. (B) 30/30 μm fi lm, scale bar: 30 μm, 200× magni fi cation.

For this study, we set out to investigate these previously developed micropatterned poly(lactide-co-glycolic acid)(PLGA) fi lms as a local, controlled FK506 delivery system.Polyesters (PLGA, poly(Lactic acid) (PLA), poly(ε-caprolactone) (PCL), etc.) have been widely studied for the development of drug delivery systems for the delivery of small molecules in various clinical applications, therefore making our previously developed PLGA micropatterned films a prime candidate for the creation of a combination technology encompassing topological guidance cues and local, controlled delivery of FK506 (Pillai and Panchagnula, 2001).

We hypothesized that the micropatterned PLGA film sembedded with FK506 could release FK506 in a therapeutic range over an extended period of time (Figure 1). Characterization testing of the FK506 embedded micropatterned PLGA films was performed in this study. These micropatterned PLGA fi lms capable of extended, localized delivery of FK506 have the potential to be used in the construction of nerve repair devices.

Materials and Methods

Flat and micropatterned mold fabrication

Flat and micropatterned PLGA films were manufactured by solvent casting onto polydimethylsiloxane (PDMS) molds.PDMS molds were created using a previously developed photolithography technique (Li et al., 2018). The photolithography process was performed to produce both 10/10 μm(groove width/ridge width) and 30/30 μm micro-patterns on a silicon substrate which PDMS was cast on to create the inverse mold for fi lm production. AZnLOF2020 (Microchemicals, Ulm, Germany) negative photoresist was coated on the surface by spin coating with a series of rotating speeds (30 r/min 5 seconds, 500 r/min 5 seconds and 1400 r/min 45 seconds). The silicone substrates were soft baked at 110°C using a hotplate for 1 minute. Silicon substrates with photoresist were exposed to ultraviolet light by OAI 200 mask aligner(OAI, San Jose, CA, USA) for 8.5 seconds. AZ 1:1 developer solution (Microchemicals) was applied for 45 seconds, and then rinsed with deionized water for 1 minute. Silicon substrates were dried with N2 gas and the silicon substrate mold was obtained. To create the inverse micro-patterned PDMS molds, 20 mL PDMS (10:1, v/v) was poured onto the silicone mask and degassed in a vacuum for 30 minutes. The PDMS molds were left to cure at room temperature for 24 hours on a leveling table and then at 80°C for 2 hours. A PDMS mold for the fl at, non-patterned fi lms was made by pouring 30 mL of PDMS (10:1, v/v) in a 60 mm glass petri dish and left to cure at room temperature for 24 hours on a leveling table and then at 80°C for 2 hours. A 60 mm diameter PDMS (10:1, v/v) ring was made and bonded to each PDMS mold to create a fl ange around the mold to contain the PLGA/FK506 solutions.

式中:PSTC——标准测试条件下(入射强度为1 kW/m2,外界温度为298.15 K)的最大测试功率;

FK506/PLGA solutions and fi lm casting

Con fl icts of interest: The authors have no con fl icts of interest to declare.

Micropattern design veri fi cation via scanning electron microscopy

FEI Quanta 600 FEG scanning electron microscope (SEM)(Thermo fi sher, Waltham, MA, USA) was used to verify the micropattern design speci fi cations after the PLGA fi lm fabrication was complete. The surface was coated with a 5 nm gold film(Thermofisher) by sputter for conductivity. The FEI Quanta 600 FEG (Thermo fi sher) at the Utah Nanofab of the University of Utah. Using ImageJ (ImageJ 1.31v, National Institutes of Health, Bethesda, MD, USA) the ridge and groove widths were measured (n = 10 measurements of ridge and groove each).

Weight loss

A weight loss study was conducted to evaluate the degradation rate of the various fi lms ( fl at, 10/10 and 30/30 μm groove/ridge widths with 0, 1, and 3 μg/cm2 FK506) loaded into the fi lm. 1 cm2 fi lms were cut out of each of the cast fi lms. Each fi lm was weighed prior to the start of the study to determine a starting weight and was placed into a 5 mL conical tube containing 5 mL of PBS. The conical tubes were kept at 37°C and 5% CO2 for 8 weeks. Every 7 days the PBS was aspirated and replaced with 5 mL of fresh PBS. At weeks 2, 4, 6, and 8, n = 4 fi lms of each fi lm type was removed, rinsed in DI water and left in a vacuum for 48 hours to dry for weighing. Material degradation rate was calculated by the following equation (Wo is original dry weight prior to test and Wn is dry weight at time point n):

In vitro FK506 release characterization

An in vitro drug release test was conducted to determine the release rate of FK506 from the PLGA films. 1 cm2 film devices were cut out of each casted film (flat, 10/10, 30/30 with 0, 1, and 3 μg/cm2 FK506 concentrations), disinfected by washing in 70% ethanol, and placed in a 24-well plate with 2 mL of culture media (Gibco™ DMEM F12 + 10%FBS + 1% Pen-Strep) in each well (n = 8 for each group). The fi lms were incubated at 37°C and 5% CO2 for 56 days. The 2 mL media samples were collected and replaced with fresh media at 24 hours and then every 72 hours for 28 days. The concentration of FK506 within the samples was determined using an ELISA (Abnova, Taiwan, China) and then the mass of released FK506 calculated.

不管怎么说，我认定了自己的这个选择，同时也隐约地感觉到，它只会带给我惊喜和收获。我只需顺着这条道路往下走，就能越走越宽阔。

FK506 bioactivity evaluation

Figure 2 FK506 release pro fi les of the various PLGA fi lms.

In vitro drug release testing was performed to determine the FK506(Tacrolimus) release pro fi les from the various PLGA fi lms. PLGA fi lms with 1 μg/cm2 and 3 μg/cm2 initial loading concentrations were used for this study with either flat, 10/10 μm, or 30/30 μm micropatterns. The rate is presented in ng/day ± SEM, n = 8 per group for this experiment. 1 μg/cm2 fi lms were discontinued after day 28 due to the fact that they were releasing drug at such a low rate. PLGA:Poly(lactide-co-glycolic acid).

Figure 3 Dorsal root ganglion neurite extension assay for FK506(Tacrolimus) bioactivity assessment.

(Top) Phase-contrast images of the dorsal root ganglions (DRGs) cultured for 72 hours which were used for average neurite extension assessment.(A) DRG grown in 0 ng/mL FK506 control media (B) DRG grown in 10 ng/mL control media (C) DRG grown in collected media from 3 μg/cm2 fi lm drug release. (D) Neurite extension values of DRGs cultured in media collected during the drug release test.Neurite extension was evaluated and compared to known FK506 concentrations 0 and 10 ng/mL to verify that drug retains its bioactivity after being released from the films (n = 8 per 0 and 10 ng/mL control groups and for experimental groups n = 3 per time point for a total of n = 12 per flat,10/10, and 30/30). *Indicates groups that are significantly different (P ＜0.05) from the 0 ng/mL control and are not signi fi cantly different (P ＞ 0.05)from the 10 ng/mL control.

The collected media samples from the in vitro FK506 rate of release testing were used for the bioactivity study. The 3 μg/cm2 fi lms were used for the bioactivity study, 3 collected media samples were chosen per group per time point for evaluation (n = 3 per sample and day 1, 16, 35, and 49 were evaluated). Control groups of 0 ng/mL and 10 ng/mL FK506 were used for comparison (n = 8 per control group, dorsal root ganglions (DRGs) were tested) and for the experimental groups a total of 12 DRGs for each timepoint and group were cultured. Fertilized chicken eggs (Merrills Poultry, ID,USA) were incubated at ～39°C under 100% relative humidity for 12 days. The eggs were cleaned with 70% ethanol and then opened to extract the embryos. DRGs were dissected from the embryos under a microscope using a previously published method (Labroo et al., 2017b). 24-well plates were coated with laminin (1 μg/mL), then 500 μL from each media sample was placed into 3 wells. Chick DRGs were separated carefully from connective tissue for culturing and a single DRG was placed into each well with the 500 μL of media sample (n = 3/group). The plate was incubated for 72 hours at 37°C and 5% CO2 to evaluate the released drug’s bioactivity. After 72 hours the media was aspirated from the wells, the DRG’s were fi xed with methanol and rinsed with deionized water. Each DRG was imaged using a wide field light microscope at 4× magni fi cation. Images of DRGs were used to analyze neurite extension. Neurite extension measurements were done using a previously described method(Labroo et al., 2017a). Brie fl y, the area of the ganglion body(ADRG) and the total area of the DRG with the growing axons(Atot) were measured using ImageJ (ImageJ 1.31v, National Institutes of Health, Bethesda, MD, USA). The average neurite length (lavg) was calculated by: lavg= (Atot/π)1/2− (ADRG/π)1/2.

Table 1 Results of the weight loss study

Relative change values are presented in % change of initial weight of the poly(lactide-co-glycolic acid) fi lm. At each time point n = 4 fi lms per group were dried and weighed. Values are presented as % weight loss ±SD relative to the initial weight.

Flat (%)10/10 (%)30/30 (%)Week 2 22.1±0.46 19.9±0.92 22.2±0.86 Week 4 21.5±1.11 22.5±1.25 23.0±0.92 Week 6 20.1±2.30 23.2±6.19 20.1±1.76 Week 8 17.5±1.51 17.4±0.28 21.2±0.88

Statistical analysis

This study was limited to in vitro analysis of the drug-releasing capabilities of the micropatterned films and in vitro bioactivity assessment. Future studies will investigate the efficacy of these films in vivo. The micropatterned PLGA film drug delivery system investigated in this study has the potential to be used in various peripheral nerve injury models by incorporation into different devices (nerve conduits and nerve wraps). The micropatterned films could be used to line the inner lumen of nerve conduits to provide surface topological guidance, drug delivery, and a physical barrier simultaneously.Bioresorbable nerve wraps are used in the clinic to prevent immune cell in fi ltration, reduce scarring, and limit nerve adhesion to surrounding tissues (Masear, 2011; Kokkalis et al.,2015). FK506 embedded PLGA fi lms developed in this study can be wrapped around crush, stretch, direct-suture repair,autograft and allograft repairs to provide a physical barrier to impede infiltration of immune cells and prevent undesirable nerve adhesion to surrounding tissue while simultaneously delivering FK506 to the peripheral nerve injury site. In vivo investigation in various injury and repair models is needed to assess the nerve regeneration efficacy of these multi-functional micropatterned PLGA with added drug delivery capabilities.

Results

Flat and micropatterned PLGA fi lm characterization

Financial support: None.

Institutional review board statement: IACUC approval was not required for the experiments performed in this study in accordance with the University of Utah’s IACUC Guidelines.

Flat and micropatterned PLGA fi lm in vitro FK506 release pro fi le

An in vitro drug release assay was used to determine the release kinetics of FK506 from the embedded PLGA fi lms over a 56 day period. The samples were collected every 72 hours but the data is reported in average mass release per day. For the fi rst 28 days, the 1 and 3 μg/cm2 FK506 fl at fi lms released an average of 3.58 ± 2.95 ng and 12.8 ± 7.79 ng per day,respectively. For the fi rst 28 days the 10/10 1 and 3 μg/cm2 FK506 fi lms released an average of 1.65 ± 1.04 ng and 12.4 ±7.14 ng per day, respectively. For the fi rst 28 days, the 30/30 1 and 3 μg/cm2 FK506 fi lms released an average of 1.83 ± 1.57 ng and 13.1 ± 10.3 ng per day, respectively. Figure 2 shows a more detailed depiction of the release profile, displaying the average mass/day values for every time point. Statistical analysis found no significant distances between the release the 10/10 and 30/30 micropatterned groups, indicating that the size of the micropatterns did not have an effect on the drug release rate. After day 28, the 1 μg fi lms were discontinued from the study because they were releasing at undesirably low levels, and the 3 μg fi lms were continued on for an additional 28 days. From days 29–56, the fl at, 10/10, and 30/30 3 μg/cm2 fi lms released an average of 3.61 ± 1.01, 6.53± 1.09, and 9.33 ± 2.39 ng per day, respectively.

In vitro FK506 biological activity

Cell culture media samples that were collected from the drug release study were used to culture whole DRGs to evaluate the bioactivity of the FK506 released from the films. DRG neurite extension was measured to evaluate FK506 bioactivity. 10 ng/mL of freshly prepared FK506 was used as the positive control and a 0 ng/mL FK506 solution was used as a negative control. DRGs were cultured in media collected from the 3 μg/cm2 films (flat, 10/10, and 30/30) at days 1,16, 35, and 49. The average DRG neurite extension for all the time points and groups was 596 ± 30.3 μm treated with FK506 containing samples collected from the drug release test and the average DRG neurite extension for the 0 and 10 ng/mL control groups were 333 ± 82.04 μm and 671 ± 69.0 μm, respectively. Data for individual groups and timepoints can be seen in Figure 3. All groups were found to be signi fi cantly higher (P ＜ 0.05) than the 0 ng/mL control group except 30/30 Day 49. No differences were found from all experimental groups compared with the 10 ng/mL (P ＞ 0.05).

Discussion

Previous studies condu cted by others have given systemic delivery of FK506 to investigate the neurotrophic effects of FK506, but less is known about localized delivery of FK506 to nerve injuries (Gold et al., 1994, 1995, 1997; Doolabh and Mackinnon, 1999; Lee et al., 2000; Navarro et al., 2001; Udina et al., 2003, 2004; Yan et al., 2012; Konofaos and Terzis,2013; Que et al., 2013). Recently, local application of FK506 to peripheral nerve injuries has been studied with positive results indicating local delivery of FK506 to peripheral nerve injuries can improve nerve regeneration outcomes (Azizi et al., 2012; Mekaj et al., 2017). Both of these studies did not incorporate a drug-carrier to control the release of the drug,a physical barrier to prevent tissue adhesion, or the ability to provide structural support to bridge nerve gaps. Additionally, Tadjaran et al. (2015) demonstrated that PLGA microspheres loaded with FK506 can provide controlled release of FK506, but these microspheres would need to be used in conjunction with other technologies such as nerve conduits and wraps in order to be useful in many nerve repair scenarios (Tajdaran et al., 2015). The technology developed in this study differs from the other local FK506 delivery strategies mentioned in that it can offer controlled release, added functionality in the form of topological guidance cues for regenerating axons, and the ability to be used to construct nerve conduits and wraps combined into one technology, whereas others are limited in their functionality and use.

The goal of this project was to assess the drug delivery capabilities of previously developed micropatterned PLGA fi lms (Li et al., 2018). These fi lms are an ideal candidate to be used as a drug delivery system because PLGA has been extensively studied for drug delivery applications over the last few decades. PLGA is ideal because of its biocompatibility,bioresorbability, and highly tunable properties such as mechanical properties, degradation rate and drug release rates(Makadia and Siegel, 2011). PLGA and other polyesters have obtained FDA approval for various clinical applications,including nerve conduits and wraps (Kehoe et al., 2012).FK506 has shown to increase nerve regeneration outcomes by multiple mechanisms including increasing axon regeneration rates, increasing Schwann cell proliferation, and by reducing scarring at the repair site (Gold et al., 1995; Fansa et al., 2000; Udina et al., 2003; Atkins et al., 2006). FK506 is an ideal candidate drug for a PLGA based drug delivery system because both FK506 and PLGA are hydrophobic materials. The hydrophobic nature of FK506 allows it to readily disperse in the hydrophobic PLGA polymer network which allows for higher control and duration of the release. It was hypothesized that micropatterned PLGA films homogenously loaded with FK506 would be capable of an extended,localized, and scalable release of FK506.

SEM was used to observe the surface patterns of the FK506 containing micropatterned PLGA fi lms, and analysis of the SEM images verified that our fabrication technique could produce micropatterned films with longitudinally aligned ridges and grooves of varying dimensions. The 10/10 ridge width was slightly larger than the designed 10 μm, and the 30/30 ridge width was slightly smaller than designed 30 μm. These variations can be attributed to the nature of molding and can be accounted for in the future production of molds by scaling. Qualitatively, the micropatterns on the PLGA films appeared crisp and complete across the whole film. Data from the weight loss study showed an increase in weight of about 20% in the fi rst two weeks and then the weight did not change for the remainder of the time points(weeks 4, 6, and 8). The observed weight gain was contradictory to what would be expected to occur during an in vitro PLGA degradation study (Lu et al., 1999). The increase in weight could have been caused by swelling and potentially trapping of water molecules and salts that could not escape during the drying process (Tang and Hunt, 2006).

Author contributions: Concept, design, definition of intellectual content,literature search, experimental studies, data acquisition, data analysis, manuscript preparation: BD. Manuscript preparation, experimental studies, data acquisition: SW. Experimental studies, data acquisition: PL. Concept, design,definition of intellectual content, manuscript review: JS. Concept, design,de fi nition of intellectual content: HS. Concept, design, de fi nition of intellectual content, manuscript review: BG. Guarantor, concept, design, de fi nition of intellectual content, manuscript editing and manuscript review: JA. All authors approved the fi nal version of this paper.

国内企业：平信200元/年(请务必确认贵司地址能够收取平信)，快递320元/年(推荐采用此种邮寄方式)；国外及港台地区企业：700元/年(120美元/年，含邮费，EMS除外)。零售价：18元/本。

One-way analysis of variance with Tukey’s post-hoc test was performed on the DRG neurite extension bioactivity assay.A Student’s t-test was performed on the drug release data.Values of P ＜ 0.05 were considered significant. Statistical analysis was performed in Microsoft Excel 2010 (Microsoft,Redmond, WA, USA).

Conclusion

We have successfully developed a bioresorbable micropatterned PLGA film drug delivery system capable of extended, controlled, and localized FK506 delivery for use in the construction of peripheral nerve repair devices. The FK506 embedded PLGA fi lms were fabricated with a surface ridge/groove micropattern using a photolithographic technique to promote neural cell alignment and growth (Li et al., 2018).Results of this study exhibited that bioactive FK506 can be released over a period of 56 days within a therapeutic range.Additionally, the amount of FK506 released per day can be tailored by altering the initial loading concentration of the FK506/PLGA films. These FK506-containing PLGA films were developed for potential use in various peripheral nerve repair scenarios including nerve wrapping of non-transection injuries or direct suture repaired transection injuries, lining the inner lumen of nerve conduits for gap-injury repair, and wrapping around autograft/allograft repairs to increase func-tional outcomes. This technology allows for extended, localized delivery of FK506 to the repair site while avoiding the side-effects associated with systemic delivery of FK506.

The drug release study veri fi ed that FK506 could be released over a period of two months and is characterized by a byphasic release. Statistical analysis found no differences in release rates of the 10/10 and 30/30 drug release rates, this result was expected because the release of a hydrophobic drug from 75:25 PLGA is primarily dependent on bulk diffusion and bulk erosion. Bulk eroding polymer drug delivery systems, such as many polyesters, release drug based on the bulk erosion rate of the speci fi c material used, while surface area has a diminished effect (Uhrich et al., 1999; Makadia and Siegel, 2011).PLGA-based drug delivery systems have been shown to have a biphasic release curve, characterized by an initial phase based on bulk diffusion and then as bulk erosion of the polymer frees the entrapped drug molecules for release (Faisant et al., 2002).An initial higher concentration burst occurred in the fi rst 16-19 days and then a slower steadier release occurred from day 20 on. This phenomenon could be explained by FK506 molecules which are weakly interacting with the polymer matrix initially diffusing out of the fi lm when the fi lm is exposed to the aqueous solution, and then as the polymer matrix erodes,the more entrapped FK506 is freed to diffuse out of the fi lms(Makadia and Siegel, 2011). Use of a small fraction of DMSO in the polymer-drug solution may have formed a semi-porous fi lm which would allow an initial uptake of water into the fi lm causing the initial burst phase of the drug release. It was found that the release is scalable and can be tuned for speci fi c applications which may require differing dosages and sizes of fi lms to be used. Bioactivity testing found that the FK506 released from the fi lms retains its bioactivity and that neurite extension was found to be similar to the 10 ng/mL control group (previous studies found 10 ng/mL to be an optimal dosage for chick DRG neurite extension (Labroo et al., 2017a)).

To make the FK506 (Astellas Pharma, Northbrook, IL, USA)containing PLGA solutions, 10 g of 75/25 poly-lactic-glycolic-acid (Evonik Industries, Essen, Germany) was dissolved in 20 mL acetone and stirred at 60 r/min at room temperature for 2 hours. 6 mL of 100% ethanol was added to the solution,and stirring continued at room temperature for 2 days for complete dissolution of the PLGA.Two different concentrations of FK506/PLGA solutions were made to produce fi lms with 1 and 3 μg/cm2 FK506 of the fi nal casted fi lm. A solution without drug was made with 0 μg/cm2 FK506. FK506 was dissolved in 100% dimethyl sulfoxide (DMSO) and used for dilutions. Each solution was mixed at a ratio of 90/10%PLGA/DMSO. Micropatterned fi lms were made with either ridge/groove ratios of 10/10 μm widths or 30/30 μm widths and flat non-micropatterned films were made for each FK506 concentration. Each type of FK506/PLGA solution was poured into a PDMS mold and left at room temperature for 48 hours to cure and then in a vacuum for 12 hours.

大数据+农业有效促进知识产权创新与现代化农业建设的深度融合，“三农”知识产权创新创业机会逐渐显现，使我国农业规模化、标准化、低成本化、高效益化成为可能。关于农村地区基础设施薄弱的问题，还需要将大批创新人才引入一线去发现问题、解决问题。随着农产品消费观念和定义发生转变，生态农业、乡村文明等目标被提上日程，市场需求带动创新团队发展，为“三农”知识产权创新人才团队提供了充分施展才能的平台。

虽然很多互联网企业建立了员工绩效考核体系，但并没有一贯地坚持下去，这主要是由于公司高层对其不够重视。很多互联网企业的大多数部门负责人表面上很重视、支持考核，但实际上，他们总是借故工作繁忙而没有把绩效考评放在心上。很多时候，直到考核周期快结束时，部门负责人才匆忙地根据一些主观印象给员工打分。

Pictures of micropattern ridge/groove topography can be seen in Figure 1A and B. The 10/10 films had an average ridge and groove width of 10.7 ± 0.419 μm and 7.76 ± 0.596 μm, respectively. The 30/30 fi lms had an average ridge and groove width of 28.9 ± 0 .788 μm and 27.4 ± 0.682 μm, respectively. Additionally, a weight loss test was conducted to determine the degradation rate of the PLGA fi lms. Four time-points (2, 4, 6 and 8 weeks) were used to determine the weight loss pro fi le of the PLGA fi lms. Weight loss values are shown in Table 1.

从商品蛋鸡效益来看，2018年前8个月鸡蛋平均出厂价为7.69元/千克，同比上升35.10%。平均鸡蛋成本 7.35元/千克，同比增加2.90%。平均淘汰鸡价格为16.21元/只，同比上升15.80%。只鸡赢利13.63元。

Biostatistics statement: The statistical analysis was developed and performed by the study investigators with assistance from the University of Utah biostatistics core as needed.

Copyright license agreement: The Copyright License Agreement has been signed by all authors before publication.

而高职院校近些年来新招的旅游专业教师大都是院校对接的青年教师，尽管这些教师受过系统的旅游专业的理论教育，但实践经验尚显不足。所以，为适应旅游行业的发展，高职院校一定要加强师资队伍建设，不断完善旅游专业教师的知识结构，进一步增强他们的实践能力[3]。同时，高职院校应鼓励和支持旅游专业教师到企业进行挂职实践，并积极进行实践创新型课题研究，从而加强对旅游行业发展状况的了解，为旅游专业提供更为科学合理的教学服务。

Data sharing statement: Datasets analyzed during the current study are available from the corresponding author on reasonable request.

随着医疗水平的不断进步和提升，剖宫产手术成为临床治疗高危妊娠产妇和分娩异常产妇的主要分娩方式，是救治母婴生命的重要手段[8]。随着我国二胎政策的开放，再次妊娠率显著上升，因此对于再次妊娠产妇的分娩方式十分重要[9]。如何保证产妇和新生儿健康，减少产后并发症发生情况是临床产科工作的重点和难点[10]。

Plagiarism check: Checked twice by iThenticate.

Peer review: Externally peer reviewed.

Open access statement: This is an open access journal, and articles are distributed under the terms of the Creative Commons Attribution-NonCommercial-ShareAlike 4.0 License, which allows others to remix, tweak, and build upon the work non-commercially, as long as appropriate credit is given and the new creations are licensed under the identical terms.

Open peer reviewer: Kirsten Haastert-Talini, Hannover Medical School, Institute for Neuroanatomy and Cell Biology, Germany.

一大盆水，兜头盖脸，将他浇了个透心凉。他的笑声戛然而止，狼狈地弯下腰，接连吐了几口吐沫，又使劲抹了把脸。

Additional fi le: Open peer review report 1.

References

Atkins S, Smith KG, Loescher AR, Boissonade FM, O’Kane S, Ferguson MW,Robinson PP (2006) Scarring impedes regeneration at sites of peripheral nerve repair. Neuroreport 17:1245-1249.

Azizi S, Mohammadi R, Amini K, Fallah R (2012) Effects of topically administered FK506 on sciatic nerve regeneration and reinnervation after vein graftrepair of short nerve gaps. Neurosurg Focus 32:E5.

Cho MS, Rinker BD, Weber RV, Chao JD, Ingari JV, Brooks D, Buncke GM(2012) Functional outcome following nerve repair in the upper extremity using processed nerve allograft. J Hand Surg Am 37:2340-2349.

Doolabh VB, Mackinnon SE (1999) FK506 accelerates functional recovery following nerve grafting in a rat model. Plast Reconstr Surg 103:1928-1936.

Faisant N, Siepmann J, Benoit JP (2002) PLGA-based microparticles: elucidation of mechanisms and a new, simple mathematical model quantifying drug release. Eur J Pharm Sci 15:355-366.

Fansa H, Keilhoff G, Horn T, Altmann S, Wolf G, Schneider W (2000) Stimulation of Schwann cell proliferation and axonal regeneration by FK 506. Restor Neurol Neurosci 16:77-86.

Felldin M, Backman L, Brattstrom C, Bentdal O, Nordal K, Claesson K, Persson NH (1997) Rescue therapy with tacrolimus (FK 506) in renal transplant recipients--a Scandinavian multicenter analysis. Transpl Int 10:13-18.

Gold BG (1997) FK506 and the role of immunophilins in nerve regeneration.Mol Neurobiol 15:285-306.

Gold BG, Storm-Dickerson T, Austin DR (1994) The immunosuppressant FK506 increases functional recovery and nerve regeneration following peripheral nerve injury. Restor Neurol Neurosci 6:287-296.

Gold BG, Katoh K, Storm-Dickerson T (1995) The immunosuppressant FK506 increases the rate of axonal regeneration in rat sciatic nerve. J Neurosci 15:7509-7516.

Grinsell D, Keating CP (2014) Peripheral nerve reconstruction after injury: a review of clinical and experimental therapies. Biomed Res Int 2014:698256.

Hoffman-Kim D, Mitchel JA, Bellamkonda RV (2010) Topography, cell response, and nerve regeneration. Annu Rev Biomed Eng 12:203-231.

Ide C, Tohyama K, Yokota R, Nitatori T, Onodera S (1983) Schwann cell basal lamina and nerve regeneration. Brain Res 288:61-75.

Kehoe S, Zhang XF, Boyd D (2012) FDA approved guidance conduits and wraps for peripheral nerve injury: a review of materials and efficacy. Injury 43:553-572.

Kokkalis ZT, Mavrogenis AF, Ballas EG, Papagelopoulos PJ, Soucacos PN (2015)Collagen nerve wrap for median nerve scarring. Orthopedics 38:117-121.

Konofaos P, Terzis JK (2013) FK506 and nerve regeneration: past, present, and future. J Reconstr Microsurg 29:141-148.

Labroo P, Shea J, Sant H, Gale B, Agarwal J (2017a) Effect of combining FK506 and neurotrophins on neurite branching and elongation. Muscle Nerve 55:570-581.

Labroo P, Shea J, Edwards K, Ho S, Davis B, Sant HJ, Goodwin I, Gale BK,Agarwal J (2017b) Novel drug delivering conduit for peripheral nerve regeneration. J Neural Eng 14: 066011.

Lee M, Doolabh VB, Mackinnon SE, Jost S (2000) FK506 promotes functional recovery in crushed rat sciatic nerve. Muscle Nerve 23:633-640.

Lee SK, Wolfe SW (2000) Peripheral nerve injury and repair. J Am Acad Orthop Surg 8:243-252.

Li CW, Davis B, Shea J, Sant H, Gale BK, Agarwal J (2018) Optimization of micropatterned poly(lactic-co-glycolic acid) fi lms for enhancing dorsal root ganglion cell orientation and extension. Neural Regen Res 13:105-111.

Li G, Zhao X, Zhao W, Zhang L, Wang C, Jiang M, Gu X, Yang Y (2014) PorousLi G, Zhao X, Zhao W, Zhang L, Wang C, Jiang M, Gu X, Yang Y (2014)Porous chitosan scaffolds with surface micropatterning and inner porosity and their effects on Schwann cells. Biomaterials 35:8503-8513.

Lu L, Garcia CA, Mikos AG (1999) In vitro degradation of thin poly(DL-lactic-co-glycolic acid) fi lms. J Biomed Mater Res 46:236-244.

Makadia HK, Siegel SJ (2011) Poly lactic-co-glycolic acid (PLGA) as biodegradable controlled drug delivery carrier. Polymers (Basel) 3:1377-1397.

Masear VR (2011) Nerve wrapping. Foot Ankle Clin 16:327-337.

Mekaj AY, Manxhuka-Kerliu S, Morina AA, Duci SB, Shahini L, Mekaj YH(2017) Effects of hyaluronic acid and tacrolimus on the prevention of perineural scar formation and on nerve regeneration after sciatic nerve repair in a rabbit model. Eur J Trauma Emerg Surg 43:497-504.

Naesens M, Kuypers DR, Sarwal M (2009) Calcineurin inhibitor nephrotoxicity. Clin J Am Soc Nephrol 4:481-508.

Navarro X, Vivo M, Valero-Cabre A (2007) Neural plasticity after peripheral nerve injury and regeneration. Prog Neurobiol 82:163-201.

Navarro X, Udina E, Ceballos D, Gold BG (2001) Effects of FK506 on nerve regeneration and reinnervation after graft or tube repair of long nerve gaps.Muscle Nerve 24:905-915.

Pillai O, Panchagnula R (2001) Polymers in drug delivery. Curr Opin Chem Biol 5:447-451.

Que J, Cao Q, Sui T, Du S, Kong D, Cao X (2013) Effect of FK506 in reducing scar formation by inducing fi broblast apoptosis after sciatic nerve injury in rats. Cell Death Dis 4:e526.

Que J, Cao Q, Sui T, Du S, Zhang A, Kong D, Cao X (2012) Tacrolimus reduces scar formation and promotes sciatic nerve regeneration. Neural Regen Res 7:2500-2506.

Su WT, Liao YF, Wu TW, Wang BJ, Shih YY (2013) Microgrooved patterns enhanced PC12 cell growth, orientation, neurite elongation, and neuritogenesis. J Biomed Mater Res A 101:185-194.

Tajdaran K, Shoichet MS, Gordon T, Borschel GH (2015) A novel polymeric drug delivery system for localized and sustained release of tacrolimus(FK506). Biotechnol Bioeng 112:1948-1953.

Tang ZG, Hunt JA (2006) The effect of PLGA doping of polycaprolactone fi lms on the control of osteoblast adhesion and proliferation in vitro. Biomaterials 27:4409-4418.

Udina E, Gold BG, Navarro X (2004) Comparison of continuous and discontinuous FK506 administration on autograft or allograft repair of sciatic nerve resection. Muscle Nerve 29:812-822.

Udina E, Ceballos D, Gold BG, Navarro X (2003) FK506 enhances reinnervation by regeneration and by collateral sprouting of peripheral nerve fi bers.Exp Neurol 183:220-231.

Uhrich KE, Cannizzaro SM, Langer RS, Shakesheff KM (1999) Polymeric systems for controlled drug release. Chem Rev 99:3181-3198.

Vaidya R, Tender LM, Bradley G, O’Brien MJ, 2nd, Cone M, Lopez GP (1998)Computer-controlled laser ablation: a convenient and versatile tool for micropatterning biofunctional synthetic surfaces for applications in biosensing and tissue Engineering. Biotechnol Prog 14:371-377.

Yan Y, Sun HH, Hunter DA, Mackinnon SE, Johnson PJ (2012) Efficacy of short-term FK506 administration on accelerating nerve regeneration. Neurorehabil Neural Repair 26:570-580.

Yao L, Wang S, Cui W, Sherlock R, O’Connell C, Damodaran G, Gorman A,Windebank A, Pandit A (2009) Effect of functionalized micropatterned PLGA on guided neurite growth. Acta Biomater 5:580-588.